Barrette Kitchen Remodeling Nationwide

Barrette Kitchen Remodeling: The Los Angeles Owner’s Guide

If you have Barrette cabinets, shelving, or drawer components in your Los Angeles kitchen and something has cracked, warped, or stopped closing the way it should, we can source and install the replacement. A typical Barrette part replacement in Los Angeles runs between $180 and $1,400 installed, depending on whether we’re swapping a single drawer glide, replacing a warped cabinet door front, or rebuilding a cabinet box that took moisture damage. Most homeowners notice the problem the same way: a drawer that started catching about a year ago now needs a hip-check to close, or a cabinet door that no longer sits flush no matter how many times you adjust the hinge.

Call (936) 259-2607

We handle Barrette-compatible kitchen remodeling work alongside the brands we install most, including KraftMaid, Cambria, and Silestone. Penhallow Remodeling is an independent Los Angeles contractor, not a Barrette dealer or affiliate, so when you call us, you get a straight answer about whether the part is worth replacing or whether you’re better off putting that money toward new cabinetry.

Which Barrette Models This Applies To

Barrette’s kitchen line spans several cabinet families sold through regional building suppliers and big-box retailers across Southern California. The most common in Los Angeles homes are the Barrette Essentials and Barrette Expressions series, plus a range of pre-assembled and ready-to-assemble (RTA) boxes that share similar hardware footprints. Here’s the compatibility gotcha: Barrette changed their drawer glide mounting hole pattern around 2018 on several mid-tier lines. A glide from a pre-2018 cabinet will not line up cleanly on a post-2018 box without drilling new holes, so we always verify the date code stamped inside the cabinet box before ordering anything.

To identify the right part, pull the drawer and look for a white label on the underside or inside the side panel. It’ll show the model family and a manufacturing date. If the label is gone, the rail spacing and drawer box depth tell us what we’re working with. For OEM parts, lead time can be three to six weeks depending on the distributor. Quality aftermarket equivalents from brands like Liberty, Richelieu, and Salice often fit with zero modification and hit the truck in days. For hinge replacements on Barrette face-frame boxes, we typically use Blum or Grass motion-control hinges, which outlast the original equipment in most cases.

Signs Your Barrette Kitchen Remodeling Is Failing

• Drawer won’t stay closed, or closes too hard. This is almost always a worn or broken glide. The nylon bearing inside the track degrades over time, and once it goes flat, the drawer rides metal-on-metal.
• Cabinet door hangs crooked even after hinge adjustment. Barrette’s older stock hinges use a thinner steel than what we install now. If the adjustment screws keep slipping, the hinge body is stripped and needs replacement, not another turn of the screwdriver.
• Swelling or bubbling at the cabinet base near the sink. Water has gotten past the seal and into the particleboard substrate (the compressed wood core under the finish). In Los Angeles homes with dishwashers, this is common when the steam vent points directly at an adjacent cabinet.
• Shelves bowing in the middle, even without heavy loads. Original Barrette shelves on some lower-tier series are ⅝-inch particleboard. Under California’s dry climate, once they lose their laminate seal, they absorb whatever moisture is in the kitchen air and start to sag.
• Soft-close feature stopped working on one door but not others. The damper in the hinge is spent. It’s a small part, but you can’t rebuild it. The hinge gets replaced as a unit.

Replacement Cost & What’s Included

The spread comes down to the cabinet series, the number of parts, and whether the existing boxes are worth keeping. On a 20-year-old Barrette kitchen, replacing every glide and hinge in the room makes less sense than putting that money toward new cabinet faces or a full remodel. We’ll tell you which one makes sense, not which one makes us more money.

Every replacement we install carries a written price before any work starts and a written 365-day guarantee. The number you approve on day one is the number on the invoice.

DIY or Call Us?

Cabinet hardware is generally safe to work on. You can check the date code on your drawer box, measure the rail spacing, and replace a visible hinge yourself if you’re comfortable with a drill. The places we see DIY go wrong are drawer glides that need new mounting holes drilled into the cabinet box, and any repair involving a cabinet that’s pulling away from the wall. If the case is separating from the stud because a sink leak rotted the wood behind it, the repair involves water lines, structural patching, and careful shimming. That’s not a Saturday project.

If you’ve got a Barrette part that’s failed and you want to know whether it’s worth fixing, call our office at (936) 259-2607. We’ll ask you for a few measurements and the date code if you can find it, and we’ll give you an honest read before you spend a dime.

FAQs