Tremron Kitchen Remodeling Nationwide

Tremron Kitchen Remodeling: The Los Angeles Owner’s Guide

We install Tremron-compatible kitchen remodeling components across Los Angeles, with typical projects running $16,520 – $53,100 depending on cabinet line, countertop material, and how much of the existing layout stays put. Most Los Angeles homeowners call us because a Tremron cabinet hinge has sheared off, a drawer slide has bent, or a countertop seam has separated after years of dry Valley heat and daily use. If you’re looking at a failed part and wondering whether it’s worth replacing or if the whole kitchen needs reworking, you’re in the right place.

Call (936) 259-2607

Which Tremron Models This Applies To

Tremron kitchen components vary by trim and era, and getting the right match matters. Older Tremron lines used European-style cup hinges with a 35mm bore, while some mid-range cabinets from the last decade ran factory-installed soft-close slides that are specific about clip position. The quickest way to identify what you have is to pull one hinge off and measure the cup diameter and the screw spacing. For drawer slides, look for a stamped model number on the side rail, usually near the back. We stock OEM Tremron replacement parts where still available, and we also install quality aftermarket equivalents from brands like Blum and Salice when the OEM part is discontinued or back-ordered, which happens more often than most homeowners expect. Penhallow Remodeling is an independent service provider and not affiliated with Tremron, which is worth saying plainly: we don’t get a manufacturer discount for pushing their parts, so our recommendation is based on what fits and what lasts, not what clears a warehouse shelf.

Signs Your Tremron Kitchen Remodeling Is Failing

• Cabinet doors that droop or won’t close flush: This usually means the hinge’s internal spring has worn out or the mounting plate has shifted. The fix is often a hinge replacement, not a whole new door.
• Drawers that stick, wobble, or fall off the track: Ball-bearing slides wear unevenly in LA’s dry, dusty air, and a single bent bearing can make a drawer feel like it’s fighting you every inch.
• Soft-close mechanism stopped working: The piston inside the slide or hinge loses its damping fluid over time. Once it’s gone, the drawer slams shut and the part needs swap, not adjustment.
• Countertop seams separating or caulk pulling away: Tremron counters installed over older wood substrates expand and contract with humidity swings, and after enough seasons the seams open up and let water into the cabinet boxes below.
• Laminate or veneer peeling at exposed edges: This typically starts near the dishwasher or sink, where steam and moisture hit the edge banding daily. It’s a cosmetic warning sign, but it spreads fast once the glue fails.

Replacement Cost & What’s Included

In Los Angeles, a focused Tremron repair runs anywhere from a few hundred dollars for hinge or slide replacement to $4,720 – $15,340 for replacing multiple cabinet boxes or doors. If the damage is isolated, you’re looking at parts and a couple hours of labor. If the cabinets themselves have absorbed moisture and the frames are soft, the job turns into tear-out and rebuild, which lands at the higher end. Every quote from us includes the part number, the labor line, and a written price before we pick up a tool, so the number on day one is the number on the invoice. Our 365-Day Done Right Promise applies to every repair: if a hinge fails or a seam opens again inside the guarantee period, we come back and fix it at no charge, no re-inspection fee, no service call.

DIY or Call Us?

Cabinet hardware is one of the safer repair categories in a kitchen, and a homeowner with a drill and a level can swap a hinge or slide if the part number matches. The trouble starts when the cabinet box itself is compromised, when drawer runners were installed at factory spec and shifting them throws off the face alignment, or when a countertop seam needs to be milled and re-bonded. That’s where DIY turns into a slow-motion water damage problem. “Give me the whole picture first, then we pick up the tools.” Tell us what’s failing, send a photo of the part and any numbers stamped on it, and we’ll tell you honestly if this is a Saturday project or a job for a uniformed technician. For everything else, call (936) 259-2607 and ask for Trevor. I grew up in Reseda, and I’ve been looking at LA kitchen failures long enough to know which parts are worth matching exactly and which ones are better upgraded to a stronger equivalent.

FAQs