Quikrete Driveway & Pavers Nationwide

Quikrete Driveway & Pavers: The Los Angeles Owner’s Guide

We install and repair Quikrete-compatible driveway and paver surfaces across Los Angeles, with most driveway replacements running $5,310 – $16,520 depending on square footage, demo, and base prep. If your Quikrete slab has cracked, spalled, or started sinking, the fix usually lands in the $5,310 – $14,160 range for a full concrete driveway install, or $8,260 – $21,240 if you’re upgrading to pavers. Most LA homeowners discover the failure the same way: a hairline crack after a rainy winter that widens by summer, or a corner of the slab that’s now a quarter-inch lower than the rest.

Call (936) 259-2607

Which Quikrete Models This Applies To

Quikrete makes several concrete and paver product lines, and the right fix depends on which one is in the ground. The most common in LA driveways is the Quikrete Crack-Resistant Concrete Mix, which has reinforcing fibers mixed in. For paver work, homeowners typically used Quikrete’s Paver Base and Paver Sand products, or a standard 5000 PSI mix for the structural slab. Here’s the compatibility gotcha most people miss: if your original slab was poured with a fiber-reinforced mix, a patch job with standard concrete won’t bond evenly at the edges, which is why we always check the bag label or original pour notes before touching anything. As an independent contractor, we’re not affiliated with Quikrete, but we work with their product specs every week and know which aftermarket mixes match their cure times and PSI ratings.

Signs Your Quikrete Driveway & Pavers Is Failing

• Hairline cracks running in a web pattern. This usually means the slab cured too fast, which happens a lot with LA’s dry summer heat. The surface is compromised and will keep spalling until it’s addressed.
• One corner or edge has dropped lower than the rest. In the Valley and hillside neighborhoods, this is almost always soil settling or erosion under the slab. The concrete itself is fine, but the base beneath it is done.
• White chalky powder on the surface. That’s efflorescence, and in Los Angeles’s hard water, it shows up faster than in most markets. It’s cosmetic, but it signals moisture moving through the slab, which accelerates cracking.
• Pavers that rock when you step on them. The sand base has washed out, probably near a planter or downspout. In LA’s wet winters, this spreads quickly once it starts.
• Oil stains that won’t lift and have turned soft. Oil degrades the concrete surface over time, and on older Quikrete pours it can eat down a quarter inch, creating pits that collect water.

Replacement Cost & What’s Included

In Los Angeles, a full Quikrete driveway replacement runs $5,310 – $14,160 for concrete, while a paver driveway install runs $8,260 – $21,240. The spread comes down to three things: whether we’re tearing out the old slab (demo adds $1,500 – $3,000), how much base prep the soil needs (LA clay expands and contracts, so we often need to add structural fill or geotextile fabric under the new pour), and whether you want a finish upgrade like broom texture, stamped patterns, or a tinted sealer. Every quote we write includes demolition, haul-away, base prep, material, pour, finishing, and a 365-Day Done Right Promise in writing. If anything fails inside the year, we come back and fix it at no charge.

DIY or Call Us?

For a driveway or paver walkway, the realistic DIY ceiling is a small paver patch or replacing a few shifted pavers. You can pull up the affected area, re-level the base sand, and reset them. But if the issue is a cracked structural slab, a sinking section, or failed base under your driveway, this is not a weekend job. A wheelbarrow of bagged mix won’t cure to match the surrounding concrete in LA’s sun, and the first time you park a car on a bad patch it crumbles. Concrete work also involves silica dust and wet cement that can burn skin, so we’d rather you not. Call us at (936) 259-2607, tell us what you’re seeing, and we’ll give you a written price before any work starts. Give me the whole picture first, then we pick up the tools.

FAQs